![\"\"](\"https:\/\/jeffwerner.ca\/wp-content\/uploads\/2018\/03\/IMG_9334-edit-hires.jpg\")
<\/a><\/p>\nFrom left-to-right, top-to-bottom. All new unless otherwise stated:<\/p>\n
- \n
- Front forks (original)<\/li>\n
- bar end mirrors (no name)<\/li>\n
- Emgo scrambler \/ tracker handlebar<\/li>\n
- Motogadget Motoscope Tiny speedometre<\/li>\n
- Motogadget m.unit blue digital controller<\/li>\n
- Rubber grommets, assorted<\/li>\n
- Mufflers (original)<\/li>\n
- Posh blinker and tail lights<\/li>\n
- Motogadget m.switches (three button)<\/li>\n
- LED 1156 and 1157 bulbs<\/li>\n
- Motogadget m.button (digital relay)<\/li>\n
- LED light (for charging lamp)<\/li>\n
- Tommaselli Vintage Dual Pull\u00a0Throttles<\/li>\n
- Toggle switch, waterproof<\/li>\n
- Electrical terminals (various\u2026many dozens)<\/li>\n
- Exhaust nut wrench<\/li>\n
- Front brake caliper (original)<\/li>\n
- Venhill custom cable kit (clutch and throttle)<\/li>\n
- Fuel line (braided)<\/li>\n
- Buss bar<\/li>\n
- Heat shrink adhesive lined<\/li>\n
- Zip ties (plastic, stainless, low profile)<\/li>\n
- Grote LED head light lamp<\/li>\n
- Emgo 7″ vintage head light bucket<\/li>\n
- IKON rear shocks<\/li>\n
- BMW tank badges (new)<\/li>\n
- Rear wheel cover gasket<\/li>\n
- Bing carbs, with new rubber, and new carb kit<\/li>\n
- 12V test light<\/li>\n
- GXL wire (16 and 20 gauge)<\/li>\n
- Splice crimps<\/li>\n
- Deutsch connectors and terminal crimp tool, and release tool<\/li>\n
- Exhaust headers (original)<\/li>\n
- Final drive (original)<\/li>\n
- Spark plug wires and plugs<\/li>\n
- rim strips<\/li>\n
- inner tubes<\/li>\n
- battery holder<\/li>\n
- battery cable and terminals and heat shrink<\/li>\n
- vinyl loom<\/li>\n
- braided split loom<\/li>\n
- Ignition key (original)<\/li>\n
- Oil filter<\/li>\n
- Air filter<\/li>\n
- Rear brake shoes<\/li>\n
- Drive shaft (original)<\/li>\n
- Shift lever (original)<\/li>\n
- Brake lever\u00a0(original)<\/li>\n
- Drive shaft bolts<\/li>\n
- Drive shaft boot<\/li>\n
- Tesa tape<\/li>\n
- Sub frame (custom)<\/li>\n
- Gas cap (original) and new gasket<\/li>\n
- Gas tank\u00a0(original)<\/li>\n
- Front wheel\u00a0(original)<\/li>\n
- Front axle\u00a0(original)<\/li>\n
- Frame\u00a0(original)<\/li>\n
- Ignition coil and bracket (Dyna)<\/li>\n
- Voltage regulator<\/li>\n
- Foot pegs\u00a0(original) and new rubber<\/li>\n
- Brake foot lever arm\u00a0(original)<\/li>\n
- Front brake master cylinder\u00a0(original) with overhaul kit<\/li>\n
- Horn\u00a0(original)<\/li>\n
- Rear axle<\/li>\n<\/ul>\n
Borrowed a friend’s nice SLR, put on a wide angle lens, and camped out in the rafters, running up and down the ladder to get the layout. Left a spot open for the rear wheel and engine, when they come in, and can swap out the tank, forks, and mufflers for the new ones when we decide on ’em \/ find ’em.<\/p>\n
![\"\"](\"https:\/\/jeffwerner.ca\/wp-content\/uploads\/2018\/04\/IMG_20180218_160656-1-768x576.jpg\")
<\/a>Testing layouts and ladder muscles.<\/figcaption><\/figure>\n ![\"\"](\"https:\/\/jeffwerner.ca\/wp-content\/uploads\/2018\/04\/IMG_20180218_151725-1-768x576.jpg\")
<\/a>Clean concrete slate.<\/figcaption><\/figure>\n ![\"\"](\"https:\/\/jeffwerner.ca\/wp-content\/uploads\/2018\/04\/IMG_20180219_165826-768x1025.jpg\")
<\/a>Brought the heater up there with me (0\u00baC in the garage this week).<\/figcaption><\/figure>\n ![\"\"](\"https:\/\/jeffwerner.ca\/wp-content\/uploads\/2018\/04\/IMG_20180218_181813-768x576.jpg\")
<\/a>That massive order with Eastern Beaver took the longest.<\/figcaption><\/figure>\n ![\"\"](\"https:\/\/jeffwerner.ca\/wp-content\/uploads\/2018\/04\/IMG_20180218_183609-1-768x576.jpg\")
<\/a>More testing.<\/figcaption><\/figure>\n